PMC LASER BONDER · REV 0.2.3 · 2026-10-28

HMI operating illustrations

Figure-placement guide for the user manual. Video-derived reconstructions; example values. This is not an approved operating procedure or a software-validation result.

Open source / reconstruction comparison gallery

Home screen and operating states

These states show individual video examples; the recipe-2 screen comes from the login video, not a continuous reset sequence.

Home screen — idle example.
F01. Home screen — idle example.主頁.mp4 · 00:35.0
Home-screen readbacks during the demonstrated motor-reset sequence.
F21. Home-screen readbacks during the demonstrated motor-reset sequence.主頁.mp4 · 00:55.500
Home screen with the negative X work direction selected.
F22. Home screen with the negative X work direction selected.主頁.mp4 · 01:12.625
Home screen with the operation-start switch enabled.
F02. Home screen with the operation-start switch enabled.主頁.mp4 · 01:38.0
Home screen displaying recipe 2.
F23. Home screen displaying recipe 2.登陸.mp4 · 00:00.000

Recipe editing and saving

Use full-context illustrations when the reader needs to locate the input field or the operation behind a message.

Recipe editor showing steps 1–5 on page 1 of 3.
F07. Recipe editor showing steps 1–5 on page 1 of 3.配方.mp4 · 00:00.0
Recipe 1 general parameter fields above the step table.
F40. Recipe 1 general parameter fields above the step table.配方.mp4 · 00:00.000
Recipe editor with the rotational-speed numeric keypad open.
F26. Recipe editor with the rotational-speed numeric keypad open.配方.mp4 · 01:08.000
Recipe editor after the save operation, with the success message displayed.
F27. Recipe editor after the save operation, with the success message displayed.配方.mp4 · 01:17.600
Recipe editor with confirmation to save the recipe to recipe number 1.
F28. Recipe editor with confirmation to save the recipe to recipe number 1.配方.mp4 · 01:21.500

Recipe selection and loading

The list-selection and success-message examples show recipe 2. The subsequent table contains the readable steps from recipe 2. The upper-right label is transcribed as Backup and restore; the associated workflow is not shown.

Recipe list showing selection, reordering, loading, copying, moving and deleting controls.
F12. Recipe list showing selection, reordering, loading, copying, moving and deleting controls.配方.mp4 · 01:28.0Upper-right label: Backup and restore. View video evidence.
Recipe list with recipe 2 selected before loading.
F25. Recipe list with recipe 2 selected before loading.配方.mp4 · 01:37.500Upper-right label: Backup and restore. View video evidence.
Recipe list after loading recipe 2, with the success message displayed.
F29. Recipe list after loading recipe 2, with the success message displayed.配方.mp4 · 01:38.400Upper-right label: Backup and restore. View video evidence.
Full recipe editor after loading recipe 2, showing steps 1–5 on page 1 of 3.
F15. Full recipe editor after loading recipe 2, showing steps 1–5 on page 1 of 3.配方.mp4 · 01:46.0Video transcription: R initial 28; laser-test 12.00; save target 1. View source evidence and reading confidence.
Recipe 2 step table, showing steps 1 through 5 on page 1 of 3.
F24. Recipe 2 step table, showing steps 1 through 5 on page 1 of 3.配方.mp4 · 01:46.250

Manual jogging and commands

Compare displayed positions before and after the demonstrated jogging segment. A visible button alone does not establish that the function was tested.

Manual control screen for R-, X- and Z-axis jogging.
F16. Manual control screen for R-, X- and Z-axis jogging.調試.mp4 · 00:00.0
Manual-jog screen with changed R- and X-axis position readbacks.
F30. Manual-jog screen with changed R- and X-axis position readbacks.調試.mp4 · 00:19.000
Manual-screen reset, motor-stop, laser-test and precision-positioning buttons.
F39. Manual-screen reset, motor-stop, laser-test and precision-positioning buttons.調試.mp4 · 00:00.000

X-axis speed entry and positioning

The video changes X-axis speed 20 → 30 → 50 → 20 mm/s. The target field remains 20.00 mm. F35 is a transient return-to-zero readback; F17 is the later 20.00 mm readback.

Precision-positioning screen before the demonstrated X-axis move.
F31. Precision-positioning screen before the demonstrated X-axis move.調試.mp4 · 00:46.000
Precision-positioning screen with the X-axis speed keypad open.
F34. Precision-positioning screen with the X-axis speed keypad open.調試.mp4 · 00:52.000
Precision-positioning screen after the X-axis speed is changed to 30.00 mm/s.
F32. Precision-positioning screen after the X-axis speed is changed to 30.00 mm/s.調試.mp4 · 00:54.250
Precision-positioning screen with X-axis speed set to 50.00 mm/s.
F33. Precision-positioning screen with X-axis speed set to 50.00 mm/s.調試.mp4 · 01:02.750
X-axis position readback during the demonstrated return-to-zero sequence.
F35. X-axis position readback during the demonstrated return-to-zero sequence.調試.mp4 · 01:09.000
Positioning screen with axis speed, target position and return-to-zero controls.
F17. Positioning screen with axis speed, target position and return-to-zero controls.調試.mp4 · 01:18.0

Axis control details

Use these close-ups to identify the input fields and command buttons. X5/X6/X4 are transcribed labels only; their hardware meaning is unconfirmed.

R-axis precision-positioning controls.
F36. R-axis precision-positioning controls.調試.mp4 · 00:46.000
X-axis precision-positioning controls and position readback.
F37. X-axis precision-positioning controls and position readback.調試.mp4 · 01:18.000
Lens Z-axis precision-positioning controls.
F38. Lens Z-axis precision-positioning controls.調試.mp4 · 00:46.000

System settings

Show the power fields and homing-speed fields separately when explaining them.

System screen showing power-related fields and axis return-to-zero speeds.
F20. System screen showing power-related fields and axis return-to-zero speeds.系統.mp4 · 00:34.0
System laser-frequency, power-setting, power-readback and correction fields.
F41. System laser-frequency, power-setting, power-readback and correction fields.系統.mp4 · 00:34.000
System homing-speed settings for the R, X and lens Z axes.
F42. System homing-speed settings for the R, X and lens Z axes.系統.mp4 · 00:34.000